Инструкция по эксплуатации Ide Line MELILLA XBM938

Страница 27

Advertising
background image

Once the operation time has ended the breadmaker starts the
keep warm function for 1 hour beeping every 5 minutes, except
when the program dough is selected which is not heated.

CRUST COLOUR

Except for program no. 7(dough) each program offers 3 different
degrees of crust colour, which you can select by pressing the
colour button.

- Crust Light

- Crust Medium

- Crust Dark

During the first kneading the motor will switch on and off, the
dough hook will turn by turn.
During the first rising will the thermostat switch on an off to keep
a temperature of 20 C°.
During the second kneading will the motor and thermostat switch
on an off to keep the temperature at 30 C°.
During the second rising will the thermostat switch on and off to
keep the temperature at 32 C°.
During the third rising will the thermostat switch on and off to
keep the temperature at 38 C°.
During the baking the thermostat will switch on an off to keep a
minimum temp. of 121 C°.

SETTING OF THE TIMER

All programmes can be started later, which is not recommeded

for the baking process for cakes and biscuits. If you use
ingredients such as fresh milk, fruit or onions, no pre-
programming should be selected, the baking process should be
started directly.
- Select as stated above the desired setting with the MENU

SELECTION and CRUST keys.

- With both arrow TIMING keys you can pre-program a baking

process up to 13 hours. Push the arrow key upward or
downward to prolong the duration of the baking process
shown on the display.

- The duration shown on the display indicates when the bread

will be ready. If you fill the container for instance in the
evening at 10.00 p.m. and want the bread to be ready by 7.00
am, the display must show 10:00.

- These 10 hours include a waiting period of 6 hours plus the

duration of the selected baking Process (in this case 3 hours).
+ 1 hour keep warm function.

- The breadmaker switches on automatically after 6 hours and

starts the standard baking process.

- After you have set the timer, press the START key. The

remaining time until the end of the baking process will be
displayed constantly.

Remember to press the start button to commence the timer
countdown- otherwise nothing will happen!
If you set the timer incorrectly and start has been pressed, you
are able to switch off and reset the delay period again only if
mixing has not started.

START/STOP

This button serves to start or stop the breadmaker. Only press
the button once you have selected the Program Select, crust
colour and delay timer if required. As the button is pressed you
will hear a beep the breadmaker will start and the timer display
will count down.
To stop the breadmaker press and hold this button for 3
seconds. Only do this in an emergency, as the unit will then reset
to the beginning of its program. You must then begin again, the
ingredients may be ruined and need replacement.

If the temperature in the breadmaker for a new program is still
too high from the previous use, the display shows "H:HH" after
start of the program and the breadmaker will beep without
interruptions. If this happens, please remove the pan and wait
until the breadmaker has cooled down (leave the lid open).

USING THE BREADMAKER

NOTE:
Yeast must never get in contact with any liquids before needed.
1. Open the lid and remove the baking pan by raising the handle

and twisting counter clockwise and then lift out. Place baking
pan on the work surface.

2. Ensure that the paddle is attached inside the baking pan (This

is simply to push on).

3. Measure the ingredients required and add them to the pan,

The breadmaker will mix all ingredients when switched on.

4. When adding the yeast (dry or fresh) to the baking pan, take

care that the yeast does not come into contact with water or
other liquids, as it will start to activate immediately. This
applies especially when using the delay timer.

5. Do not overfill the baking pan. This will affect the final result

of the bread and may damage the breadmaker.

6. Using the panhandle, place the baking pan in the breadmaker

and turn clockwise to the lock position, close the lid of the
unit.

7. Plug the unit into the power supply (you will hear a long

deep). The unit will automatically be set to the basic program
with the colour setting at MEDIUM.

8. Now select the required program pressing the SELECT

button until the light corresponding to the program becomes
illuminated. Do not forget to select the crust colour as well.

9. Press the start/stop program to start the unit. When the

program is completed the display shows 0.00 and you will
hear the unit beeps 10 times.

Note in manufacturing, it was necessary to grease some parts of
the unit. This is may cause emitting some vapour when it is used
for the first time.

10. When the program is completed and the bread is baked the

"keep warm" function will operate for one hour. To remind
you of this, the unit will beep 6 times every 5 minutes for a
period of 1 hour, and then switch of.

11. Take care when removing the bread. The bread is very hot. To

remove the baking pan, open the lid of the unit. As the unit
will be hot, use oven gloves to remove the pan. Using the
handle, simply twist the pan counters clockwise to the
remove position and lift out.

12. Turn the pan upside down, and gently tap the bread from the

pan. Occasionally, the paddle will stay in the loaf, wait until
the loaf is cool and the remove the paddle with a wooden
utensil to avoid damage to the non-stick surface.

13. Leave the bread on a rack to cool down, ensure ventilation

from below.

14. Always unplug the unit after use

Note:
do not open the lid while the breadmaker is operating, as this
will affect the quality of the bread, especially its ability to rise
properly.

27

XBM938IM REV 05/08/03 13:37 Side 27

Advertising